ELECTRONIC NOSES APPLICATIONS AND TECHNOLOGIES
Pampa III electronic nose: Control electronics design
Giménez, J. F.; Gillari, C. A.; Valerio, D. F.; Gasulla, D. E.; Alaniz, L. T.; Lacomi, H. A.; Arrieta C. L.
División Microelectrónica-Departamento de Electrónica Aplicada- CITEF. San Juan Bautista de La Salle 4397, Villa Martelli (B1603ALO) Buenos Aires, Argentina. Fax: +54 4709 8228, E-Mail: carrieta@citefa.gov.ar
Received November 05, 2004. In final form June 04, 2005
Abstract
The Argentine electronic nose PAMPA III is an equipment operating
with a measurement system based on a set of twelve solid state gas sensors
implemented on thin films deposited on a MEMS (Micro-Electro-Mechanical Systems)
type microheater. Solid state gas sensors were designed and built by the Institute
LAMEL-CNR (Bologna, Italy) while the thin film sensors were made in Argentina
in the frame of the cooperation project CITEFA-CNEA-FI (UBA). In this work,
the operating principle of control drivers for PAMPA III sensors is reported,
mainly considering the chosen criterion to control the power supplied to each
sensor heater and the signal conditioning circuit related to the sensing film
itself.
The e-nose enables to program, in a flexible way, its functioning parameters,
using control electronics and an associated software. Parameters to be changed
are: heating power supplied to each sensor, bias voltage on each sensible
film, velocity of the aspiration micropump etc. One of the main characteristics
of the equipment is that the control circuits for sensors are of the "constant
resistance" type.
All measurements data of PAMPA III e-nose are supplied to a PC which performs
the statistical processing, employing the pattern recognition algorithm of
Principal Components Analysis (PCA).
Resumen
La nariz electrónica argentina PAMPA III es un dispositivo que trabaja
con un sistema de medición basado en la utilización de doce
sensores de gas de estado sólido, implementados con sensores de película
delgada, depositados sobre un microcalefactor de tipo MEMS. Los sensores de
estado sólido fueron diseñados y construidos en el Instituto
LAMEL, CNR (Boloña, Italia), mientras que los sensores de película
fina fueron obtenidos en la Argentina en las instituciones que participan
del convenio de cooperación CITEFA-CNEA-FI(UBA). En este trabajo, se
presenta el principio de funcionamiento de los circuitos de control para los
sensores de la nariz electrónica PAMPA III, poniendo especial énfasis
en el criterio empleado para controlar la potencia entregada a los calefactores
de cada uno de los sensores y el circuito de acondicionamiento de señal
asociado con la película sensible propiamente dicha.
La nariz electrónica permite programar, de forma muy flexible, los
parámetros de funcionamiento, lo que se logra con una electrónica
de control y programación asociada. Los parámetros a variar
son: potencia de calefacción suministrada a cada sensor, tensión
de polarización sobre cada película sensible, velocidad de aspiración
de la microbomba, etc. Una de las características destacables del dispositivo
es que el circuito de control de los sensores es del tipo de "resistencia
constante".
La nariz electrónica PAMPA III entrega todos los datos de sus mediciones
a una computadora personal que se encarga del procesamiento estadístico,
empleando el algoritmo de reconocimiento de patrones denominado Análisis
de Componentes Principales (ACP).
Introduction
Recent advances in gas sensors technology, together with electronics development
and artificial intelligence knowledge, enabled the building of a new perceptive
instrument: the electronic nose (e-nose). This new concept in the analytical
instrumentation contributes to the fields of digitalization, simulation and
extension of knowledge on human senses as it has been done before for vision
and hearing. The measuring devices included by e-noses are gas sensors built
with different technologies for different applications. Particularly, in case
of the PAMPA III e-nose, semiconductive Metallic Oxide Gas Sensors were used.
Thin film MEMS type (Micro-Electro-Mechanical Systems) sensors are built by
evaporation deposition of thin semiconductors (SnO2, ZnO or WO3,
among others) films, which must be heated locally in a temperature range from
300 to 450 °C to detect the different gaseous species. Metallic oxide semiconductors
are usually doped with different elements (Al, In, Pd, Au, Sb, etc.) to increase
sensor selectivity.
An e-nose is constituted by three important parts which are serially operated
and act on the analyte: the specimen headspacer, the sensor sets and the system
processesing the signal. E-nose data enables to discriminate odors, it is also
possible, under certain conditions, to determine different concentrations of
the analyte (responsible of the detected odor) [1], Figure 1.
It is necessary to point out that an e-nose always operates by comparison and
that it does not perform a chemical analysis but a discrimination of odors,
enabling to separate different analytes by their odors.
Experimental Procedure
Microheating plate technologyArchitecture
of the thin film solid state sensor on the microheater
Selected thin films for the PAMPA III e-nose were deposited on a silicon supported
membrane (Si3N2) Closed Membrane Type. The membrane was
then heated between 300 and 450 °C with an integrated heating device (consisting
of a thin Pt film, deposited by sputtering). The membrane was encapsulated and
interconnected to a TO-8 capsule with a Au bonding wire (diameter: 50mm).
The membrane was used to isolate thermically the hot thin film sensor from its
substrate and capsule, thus improving considerably the yield of this heating
system in comparison with that of other known sensor architectures. This ensamble
also enabled the operation of bonding wires and microwelding at temperatures
lower than 50 °C, i.e. under normal conditions, Figure 2.
To build the microheater: on a micromachined Silicon substrate (4mm long, 4
mm wide and ~500 mm thick) a non stoichiometric SixNy
coating was grown by LPCVD (Low Pressure Chemical Vapor Deposition) [2]. In
the case of the PAMPA III e-nose, membranes obtained at the LAMEL Institute,
CNR (Bologna, Italy) were actually used for the microheater although, simultaneously,
a microheater completely designed in Argentina is being developed to replace
it.
Fig. 1. Photograph
of the electronic nose PAMPA III, detailing different stages of the electronic
circuit.
Fig.
2. Micro-hot plate scheme (NNR-LAMEL, Bologna, Italy.
Fig.3.
Comparison of two different operating conditions for a same micro-hot plate.
Electronic circuits
Control of supplied power to the heater:
The electronic circuit to control the microheater of micro-hot-plate was designed
considering the device miniaturization and the necessary conditions to operate
in the measurement chamber (air flow: ~0.5 l.min-1). The design enabled
an important temperature fluctuation on the sensitive film if abrupt changes
in the dissipation conditions occurred, mainly due to the following contributions
[3]:
- Pc:
power transferred by conduction through the membrane to the silicon structure,
- Pk: power transferred by conduction and convection to the
environment surrounding the hot membrane,
- Pr: power transferred by radiation.
Consequently, the power supplied to the heating device of a microheater (Ph) can be expressed as the sum of the three above mentioned contributions:
Ph = Pc + Pk + Pr
In the case
of this work, the useful power was part of the dissipated by conduction power
used to heat the sensitive film. A plot was done at our laboratory to compare
the functioning conditions of a heating device operating in vacuum (10-5
Torr) and under normal conditions of pressure (AP: atmospheric pressure). Figure
3 shows the plot of the heating resistance versus the supplied power under
the mentioned operating conditions. Measurement data indicated that, in order
to reach a temperature of 400 °C on the sensitive film, it was necessary
to supply 100mW (Pc + Pk + Pr) under
AP, while in vacuum only 37 mW were required (Pc + Pr)
for the same temperature. Convection effects are responsible of ~ 60% or more
of losses in the heating system at 400 °C. This effect decreased if the
heating power level decreased. Besides, if measurement data corresponding to
two different operating conditions were compared, for example: for a sensor
without and with forced convection (~0.5 l.min-1), differences of
approximately 6% for the same temperature were observed. Resistance is an indicator
of the operational temperature of the heating device. Relation between temperature
and resistance is not lineal since temperature is not homogeneously distributed
on the heater [2]. This fact was proved by microthermographies [2]. If it is
considered that temperature on the sensitive film is strongly dependent on thermal
consumption of the heater surface, it is then to define operation points for
sensors in the system constituted by the measurement chamber, the micropump
and the sensors. This point is given by two easily measurable magnitudes: the
heater resistance (Rh) and the supplied power to the heater
(Ph), this operating point being an important factor to be
considered as measurement parameter in PAMPA III. This fact shows the importance
given to the temperature control of the heating driver. In Ref. [4] it is strongly
pointed out the large influence of the operating temperature on the sensitive
film conductivity. The sensing semiconductor exhibits a thermally activated
conductivity mechanism; it is reported [6] that a temperature variation of 0.5
°C in thick films generates a conductance change of 1%. This fact, also
valid for thin films, points out that strict control of temperature variation
is of the highest importance to increase the sensors sensitivity.
Consequently, a circuit maintaining a constant heating resistance regardless
of variations of thermal solicitation on the heater, was chosen for this work
as the heating driver [5]. The circuit consisted of a Wheatstone bridge, in
which one of its resistors was the sensor heater (made of Pt and exhibiting
a high positive temperature coefficient). The other resistors should be very
stable with temperature. The bridge was fed with a Voltage Controlled Current
Source (VCCS). The differential voltage between both, opposite bridge nodes
was applied to an error/set-point amplifier, from which the controlling voltage
to the VCCS was extracted. Then, different current values were supplied to the
bridge so as to maintain at zero the error differential voltage, a situation
only reached when the bridge was in equilibrium. If the value of heater resistor
was modified, as a consequence of thermal solicitation from the measurement
chamber, the circuit tends to compensate this effect, increasing or decreasing
the power supplied to the heater and trying to maintain a constant heater resistance.
This implied that its temperature was maintained also constant because the heater
resistance only depended on temperature. The circuit is then called constant
resistance driver.
The output of the error/set-point amplifier supplied a voltage proportional
to the output differential signal of the Wheatstone bridge (error = Vnw
- Vnl) plus a set-point (Vnw) obtained
by a digital potentiometer placed on one of the bridge arms.
Vs
= Vnw + (Vnw - Vnl) RG /RA
The gain of this amplifier was approximately given by the ratio between the resistances RG and RA of the circuit of Figure 4. This digital potentiometer could be commanded by a microcontroller or a PC to digitally fix the heating power (maximal 100 mW) chosen to operate the sensor.
Fig.
4. Electronic circuit for heating control
Device to condition
the signal to the sensitive film:
A metal oxide semiconductive gas sensor is based on changes of its electrical
conductivity due to the reaction between the semiconductor and the gases present
in the gas chamber [7]. It is interesting to point out that these sensors are
unspecific, i.e. they do not sense only one gaseous species but, they are sensitive
to several species. For example: non doped SnO2 sensors built by
the RGTO (Rheotaxial Growth and Thermal Oxidation) technique are mainly sensitive
to CO, CH4, NO2, VOCs, etc. however, they also exhibit
a considerable response to humidity. In order to detect only one gaseous species,
they are usually connected in arrays of multiple sensors or include filters
to avoid the sensor exposition to the interfering species. In general, there
are several strategies to diminish the effect of parameters upsetting the sensors
response.
In Figure 5, it is shown the diagram of the circuit conditioning
the signal to the thin film sensor. It is possible to observe that the output
signal is proportional to the sensing film conductance. The circuit enables
to fix:
I) the bias voltage of the sensitive film and, indirectly, the serial resistance
hitched to the same branch where the sensor is connected,
II) the gain in the amplifying stage.
Both fittings are accomplished with digital potentiometers (consequently, to
be commanded by a smart circuit, like a microcontroller, a PC, etc.). The observation
of Figure 5 enables to deduce the following expression for
the output voltage of the circuit, proportional to the sensitive film conductivity:
Vf= - VR D(NB)[RG(NG)] / [RS + RB(NB)]
RG(NG): Gain Resistence ( funtion of Digital Control number NG )
D(NB): Divider Factor (function of Digital Control number NB)
RB(NB): Equivalent Resistence of Digital Divider (function of Digital Control number NB)
VR: refernce Voltage
This configuration was chosen because of the dispersion of the sensitive films resistance data due to different metal oxides (SnO2, ZnO, WO3, etc.) for sensitive films, to different doping elements and to the dispersion of the fabrication processes. The values of films resistance to be connected to this circuit are between 30KW and 3MW (in air and at low temperature). The described circuits are useful for each sensor and in the PAMPA III the circuitry ended up considerably complex since this e-nose has 12 sensors. Besides, two commercial sensors were included in the measurement chamber: HYH3610 and LM35 to measure humidity and temperature, respectively. The driving circuits for these sensors are not described in this work.
Figure
5: Electronic circuit for a thin film gas sensor. It includes two potentiometers
to control the amplifier gain and the voltage bias.
Conclusions
The Argentine PAMPA
III electronic nose constitutes a useful equipment built through a successful
cooperation between the CNEA (Physics Department-MEMS Group) and CITEFA Microelectronics
Division, Department of Applied Electronics. The functioning of the described
circuit topologies was proved in the engineering e-nose prototype reaching stability
in sensors operation and exhibiting a considerable versatility to choose the
system measuring format because of the availability of digital controls for
each sensor and the possibility of its control with a PC.
Acknowledgements
The authors are indebted to SECYT (PID 131 granted to A.L. at CNEA) and to the
JPA S.A. Enterprise, by their financial assistance to support this project.
Authors also would like to express their thanks to members of CINSO-CITEFA-CONICET
by fruitful discussions and cooperation to furthered this project.
References
[1] Gardener, J. W.; Barlett P. N., "Electronic Noses, Principles and Applications", Oxford Science Publications, 1999.
[2] Cardinali, G. C.; Dori, L.; Fiorini, M.; Sayago, I.; Faglia, G.; Perego; Sberveglieri, G.; Liberali, V.; Maloberti, F.; Tonietto D., "A Smart Sensor System for Carbon Monoxide Detection", Analog Integrated Circuits and Signal Processing, 1997, 14 , 275-296.
[3] Dibbern, U., "A Substrate for Thin film Gas Sensors in Microelectronic Technology", Sensors and Actuators-B (Chemical), 1990, 2, 63-70.
[4] McGeehin, P.; Moseley, P. T.; Williams, D. E., "Self-diagnostic Solid State Gas Sensors", Sensor Review, 1994, 14, 1, 13-19.
[5] Benammar, M.; Maskell W. C., "Temperature Control of Thick-Film printed Heaters", J. Phys. E: Sci. Instrum. 1989, 22, 933-936.
[6] Demarne, V.; Sanjinés, R., "Thin Film Semiconducting Metal Oxide Gas Sensors", Chapter 3, in G Sberveglieri (Ed.), Gas Sensors, Principles , Operations and Developments, (Thin Film Laboratory University of Brescia, Italy), Klumer Academic Publishers 1992.
[7] Fraigi, L. B.; Lamas, D. G.; Walsöe de Reca, N. E.., "Sensor de SnO2 nanoestructurado de película gruesa para monitoreo de gases", Microsensores de Estado Sólido para Monitoreo del Medio Ambiente (Proyecto IX.2)-Cooperación Iberoamericana-Subprograma IX Microelectrónica, 1999, 57-72.